您好,欢迎光临济南金力升降机械有限公司官方网站!
24小时服务热线:18766191320

24小时服务热线

18766191320

升降设备平台的维护保养要考虑哪些因素?

来源:http://www.jlsjj.cn     发布时间:2021-06-21   浏览次数:

固定式升降设备平台的维护保养要考虑哪些因素?
What factors should be considered in the maintenance of fixed lifting equipment platform?
导轨式升降平台压缩弹簧,阀体和阀的项圈,身体的内腔装有压力弹簧,压缩弹簧,也可以用在腔体滑动阀连接,镶嵌在护环间距身体滑阀,滑阀的顶部有一个孔,在滑阀底部的插头,连接在洞的入口和出口,阀体。
Guide rail type lifting platform compression spring, valve body and valve collar, the inner chamber of the body is equipped with pressure spring, compression spring, can also be used in the chamber sliding valve connection, inlaid in the retaining ring spacing body slide valve, the top of the slide valve has a hole, the plug at the bottom of the slide valve, connected to the hole inlet and outlet, the valve body.
因此,降低导轨式升降平台工作人员的风险,一旦管道破裂,从而降低导轨式升降平台速度太快,防爆阀迅速关闭,进入状态的调节,使台面慢慢落下,保障人身和设备的安全,从而起到安全保护的作用.这项新技术的应用使导轨式升降平台的产品变得非常大。
Therefore, reduce the risk of rail type lifting platform staff, once the pipeline breaks, so as to reduce the speed of rail type lifting platform is too fast, explosion-proof valve quickly closed, enter the state of regulation, make the table slowly fall down, protect the safety of people and equipment, so as to play the role of safety protection. The application of this new technology makes the rail type lifting platform products become very large.
随着物流业的快速发展,导轨式升降平台技术的应用越来越频繁.而且由于导轨式升降平台的多样性和高性能的适应性,受到人们的广泛喜爱.但由于导轨式升降平台笨重.仅打开保存.随着温度等各种因素的变化,导轨式升降平台的损坏非常严重,而导轨式升降平台的维护尤为重要。
With the rapid development of the logistics industry, the application of the guide rail type lifting platform technology is more and more frequent. And because of the diversity and high performance adaptability of the guide rail type lifting platform, it is widely loved by people. But because the guide rail type lifting platform is bulky, only open to save. With the change of temperature and other factors, the damage of the guide rail type lifting platform is very serious, The maintenance of the guide rail type lifting platform is particularly important.
                     山东升降设备厂家
在安装、装配和调整旋转机构时,应注意确保旋转机构加速器的中线与齿轮中线平行。加速器的啮合面不小于70%,啮合间隙应适当。
When installing, assembling and adjusting the rotating mechanism, attention should be paid to ensure that the center line of the accelerator of the rotating mechanism is parallel to the center line of the gear. The meshing surface of accelerator should not be less than 70%, and the meshing clearance should be appropriate.
1.经常反映所有电线电缆都没有损坏。有必要对损坏的部位及时进行修整和更换。
1. It is often reflected that all wires and cables are not damaged. It is necessary to repair and replace the damaged parts in time.
2.电机过热时,应及时停机,清理故障后继续运行。电机轴承应光滑。
2. When the motor overheats, it should be shut down in time and continue to run after clearing the fault. Motor bearings shall be smooth.
3.局部电刷的接触面应保持清洁,调整电刷压力,使接触面积不小于50%。
3. The contact surface of local brush should be kept clean, and the brush pressure should be adjusted to make the contact area not less than 50%.
4.控制箱、配电箱经常保持清洁,电气设备上的灰尘要及时清理。
4. The control box and distribution box should be kept clean, and the dust on the electrical equipment should be cleaned in time.
5.安全安装的行程开关的接触分、合应可靠,接触弧坑应及时打磨。
5. The contact opening and closing of the travel switch installed safely should be reliable, and the contact crater should be polished in time.
感谢您的阅读,希望以上内容能对您有所帮助,如您想了解更多精彩内容请多多关注我们的网站。
Thank you for reading, hope the above content can help you, if you want to know more wonderful content, please pay more attention to our website.

上一篇:山东升降机的正确维护很重要!
下一篇:山东家用电梯厂家的使用范围!