您好,欢迎光临济南金力升降机械有限公司官方网站!
24小时服务热线:18766191320

24小时服务热线

18766191320

铝合金升降平台日常使用注意事项!

来源:http://www.jlsjj.cn     发布时间:2021-06-25   浏览次数:

工作时我们经常会使用到铝合金升降机,所以小编在此提醒各位日常使用注意的一些事项:
We often use aluminum alloy elevators in our work, so I would like to remind you of some matters needing attention in daily use
1.使用前,必须检查限位行程开关,确保限位行程开关动作可靠,这是保证安全的重要措施;也得检查接线,确保接线正确;通电前,确保配电箱无杂物。
1. Before use, the limit travel switch must be checked to ensure its reliable action, which is an important measure to ensure safety; Check the wiring to make sure it is correct; Before power on, make sure that the distribution box is free of debris.
2.使用时,铝合金升降机的四根支腿必须支起,因为四只轮胎不受力,所以四轮铝合金升降机的下底架必须水平。
2. When using, the four legs of the aluminum alloy elevator must be supported, because the four tires are not stressed, so the lower underframe of the four-wheel aluminum alloy elevator must be horizontal.
3.必须在空间开阔且场地平整的的室外场地试用,这点是非常重要的,这样可以防止在限位失效时出现事故。
3. It is very important to try it in the open and flat outdoor field, so as to prevent accidents in case of limit failure.
4.而试载时也要进行多次,一次试载,可选择空载试验,以检验铝合金升降机的升、降速度是否合理,平台的稳定性能否达到要求,声音是否正常,能否达到额定升降高度,如果试验数据正常,可进行二次试载试验;二次试载试验可选择半载试验,着重检验平台的稳定性。如果晃动性在允许范围内,可进行第三次试验-全载试验,以确定平台在额定载荷的状态下是各项参数是否正常。如果正常,可以进行第四次试验-超载试验,可以加110%的载荷进行试验,以检验平台的防超载装置设置是否合理,如果设置正确,在超载的状态下,升降平台不能上升,如果能上升,说明升降平台超载装置设置不合理,应要求厂家重新调整设置。
4. The test load should be carried out for many times. For one test load, the no-load test can be selected to check whether the lifting and lowering speed of the aluminum alloy elevator is reasonable, whether the stability of the platform can meet the requirements, whether the sound is normal, and whether it can reach the rated lifting height. If the test data is normal, the second test load test can be carried out; Half load test can be selected for the second load test, which focuses on the stability of the platform. If the sloshing is within the allowable range, the third test full load test can be carried out to determine whether the parameters of the platform are normal under the rated load. If it is normal, the fourth test overload test can be carried out, and 110% load can be added to test to check whether the anti overload device of the platform is reasonable. If the setting is correct, the lifting platform can not rise under overload condition. If it can rise, it indicates that the overload device of the lifting platform is unreasonable, and the manufacturer should be required to adjust the setting again.
5.在试载试验通过后,方可载人使用。
5. It can be used only after passing the test.
                      山东升降设备厂家
二、铝合金升降机的定期保养非常重要
2、 Regular maintenance of aluminum alloy elevator is very important
对于铝合金升降机来说,保养是非常重要的,能够保证自己机器使用时间和使用效率都会大幅度的延长,其实对于新型机器来说,保养主要分月度保养和年度保养,在这我们也可以告诉您关于月度保养和年度保养主要应注意什么?
For aluminum alloy elevator, maintenance is very important, to ensure that their machine use time and efficiency will be greatly extended, in fact, for new machines, maintenance is mainly divided into monthly maintenance and annual maintenance, here we can also tell you about the monthly maintenance and annual maintenance should pay attention to what?
首先对于铝合金升降机月度保养需要注意以下几点:
First of all, for the monthly maintenance of aluminum alloy elevator, the following points should be paid attention to:
1.各部位均加注一些润滑油,延长轴承使用寿命。
1. All parts are filled with some lubricating oil to prolong the service life of the bearing.
2.滚轮、中间轴及轴承,油缸销轴及轴承,臂架铰轴及轴承等有无磨损。
2. Whether the roller, intermediate shaft and bearing, cylinder pin shaft and bearing, boom hinge shaft and bearing are worn.
3.液压油的油质和油位。升降平台全程升起,在这位置时,液压油面应高出箱底40-50毫米。液压油是变暗、发粘或有砂砾等异物,如有发现应及时更换。
3. Quality and level of hydraulic oil. When the lifting platform is raised in the whole process, the hydraulic oil level should be 40-50 mm higher than the bottom of the box. Hydraulic oil is darkened, sticky or gravel and other foreign matters, if found, should be replaced in time.
其次就是对于铝合金升降机年度保养,年度保养按照一定的标准可以遵循以下几点,年度是一次大的保养,所以对于以下几点需要特别大注意:
The second is the annual maintenance of aluminum alloy elevator. According to certain standards, the annual maintenance can follow the following points. The annual maintenance is a big one, so the following points need to be paid special attention to:
1.检查铝合金升降机所有的液压管道和接头。管道不得破损,接头不得松动,必须将所有接头拧紧。
1. Check all hydraulic pipes and joints of aluminum alloy elevator. The pipeline shall not be damaged, the joints shall not be loose, and all joints must be tightened.
2.卸下并拆开下降阀,用压缩空气将柱塞吹净,然后装入,重新安上。
2. Remove and disassemble the lowering valve, blow the plunger clean with compressed air, then install it and install it again.
3.把液压油放尽弃掉,拧紧接头取出油过滤器,洗清后,用压缩空气清理干净,然后放回油箱,并联接好管路。
3. Drain and discard the hydraulic oil, tighten the connector, take out the oil filter, clean it with compressed air after cleaning, then put it back to the oil tank and connect the pipeline.
做到以上几点,相信我们使用的铝合金升降机不但寿命可以得到延长,而且在使用方面的安全性也能大大的提高。
Do the above, I believe that we use the aluminum alloy elevator not only life can be extended, but also in the use of safety can be greatly improved.

上一篇:山东升降机厂家的常见异常及处理方法!
下一篇:山东升降设备生产厂家简述在夏季使用升降设备的注意事项