您好,欢迎光临济南金力升降机械有限公司官方网站!
24小时服务热线:18766191320

24小时服务热线

18766191320

升降机车发动机运转需要注意什么?

来源:http://www.jlsjj.cn     发布时间:2021-11-15   浏览次数:

升降机车发动机运转时向油箱加油。电动叉车是靠电力工作的,在利用中如果叉车动力不足往往是因为电力不足,但是也有其他原因会造成电动叉车启动机力量不足,下面电动叉车厂来分享:电动叉车启动力量不足的原因以及相应的解决方法:
Fill the oil tank when the engine of the lifting locomotive is running. The electric forklift works by electricity. In the process of utilization, if the power of the forklift is insufficient, it is often due to the lack of electricity, but there are other reasons that will lead to the insufficient power of the electric forklift starter. The following electric forklift manufacturers share: the reasons for the insufficient starting power of the electric forklift and the corresponding solutions:
可能是电池的电压不充分。解决方法:为电动叉车电池充电,或者直接调换新的电池。启动马达的电量不够,电缆线发热,电缆线两边的铜头松动。解决方法:压紧电缆线的两边铜头,调换截面更粗的电缆线。启动马达内部轴承有磨损或者过松,转子和定子有碰擦。解决方法:调换启动马达的轴承和添加润滑脂。
山东升降设备
The voltage of the battery may be insufficient. Solution: charge the battery of electric forklift, or directly replace it with a new battery. The power of the starting motor is not enough, the cable is hot, and the copper heads on both sides of the cable are loose. Solution: press the copper heads on both sides of the cable and replace the cable with thicker section. The internal bearing of the starting motor is worn or too loose, and the rotor and stator collide. Solution: replace the bearings of the starting motor and add grease.
启动马达碳刷磨损过多,转子的铜头表面有烧蚀或脏污等。解决方法:调换启动马达的碳刷和清洗加工转子的铜头。电动叉车的动力系统属于比较复杂的部件,如果自行检验如果不能断定原因,可以直接接洽电动叉车厂和谐解决。电动叉车万向传动装置的维修与养护
The carbon brush of the starting motor is worn too much, and the copper head surface of the rotor is ablated or dirty. Solution: replace the carbon brush of the starting motor and clean the copper head of the rotor. The power system of the electric forklift is a complex component. If you can't determine the cause through self inspection, you can directly contact the electric forklift factory for a harmonious solution. Repair and maintenance of universal drive device of electric forklift
电动叉车万向传动装置是由万向节叉、十字轴总成等所组成,其作用是将变速器动力传递至主减速器。传动轴传递扭矩大,速度高,工作沉重。因此,虽然其结构并不复杂,但技巧恳求却很高。否则会涌现抖震、发响,脱落声明:本次发表只代表个人看法,请勿商用。
The universal transmission device of electric forklift is composed of universal joint fork and cross shaft assembly, which is used to transfer the power of transmission to the main reducer. The transmission shaft transmits large torque, high speed and heavy work. Therefore, although its structure is not complex, its skill is very high. Otherwise, there will be shaking, ringing and falling off. Statement: This release only represents personal views and is not for commercial use.
今天的分享就是关于山东升降设备,更多的内容小编会不断的再此分享,更多的内容请继续关注我们:http://www.jlsjj.cn
Today's sharing is about Shandong lifting equipment. More content will be shared here. Please continue to pay attention to us: http://www.jlsjj.cn

上一篇:液压升降平台的工作流程!
下一篇:安装别墅家用电梯--带您畅行不一样